BeagleBone cape interface spec

This page is a fork of BeagleBone cape interface spec page on elinux. This is the new official home.

Background and overview

Important

Resources

• See Device Tree: Supporting Similar Boards - The BeagleBone Example blog post on BeagleBoard.org

• See spreadsheet with pin header details

• See elinux.org Cape Expansion Headers for BeagleBone page

• See BeagleBone Black System Reference Manual Connectors section

• See BeagleBone AI System Reference Manual Connectors section

• See BeagleBone AI-64 System Reference Manual Connectors section

Note

Below, when mentioning “Black”, this is true for all AM3358-based BeagleBone boards. “AI” is AM5729-based. “AI-64” is TDA4VM-based.

The device tree symbols for the BeagleBone Cape Compatibility Layer are provided in BeagleBoard-DeviceTrees at:

• Black: bbb-bone-buses.dtsi

• AI: bbai-bone-buses.dtsi

• AI-64: k3-j721e-beagleboneai-64-bone-buses.dtsi

The udev rules used to create the userspace symlinks for the BeagleBone Cape Compatibility Layer are provided in usr-customizations at:

More details can be found in Methodology.

Summary of cape interfaces

Note

Legend

• D : Digital general purpose input and output (GPIO)

• I : Inter-integrated circuit bus (I²C) ports

• S : Serial peripheral interface (SPI) ports

• U : Universal asynchronous reciever/transmitter (UART) serial ports

• C : CAN

• A : Analog inputs

• E : PWM

• Q : Capture/EQEP

• M : MMC/SD/SDIO

• B : I2S/audio serial ports

• L : LCD

• P : PRU

• Y : ECAP

Table 101 Overall

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
USB D+	E1	E2	USB D-
5V OUT	E3	E4	GND
GND	1	2	GND		GND	1	2	GND
3V3 OUT	3	4	3V3 OUT		D M	3	4	D M
5V IN	5	6	5V IN		D M C	5	6	D M C
5V OUT	7	8	5V OUT		D C	7	8	D C
PWR BUT	9	10	RESET		D C	9	10	D C
D U	11	12	D		D Q P	11	12	D Q P
D U	13	14	D E		D E	13	14	D
D	15	16	D E		D P	15	16	D P
D I S	17	18	D I S		D	17	18	D
D I C	19	20	D I C		D E	19	20	D M P
D E S U	21	22	D E S U		D M P	21	22	D M Q
D S	23	24	D I U C		D M	23	24	D M
D P	25	26	D I U C		D M	25	26	D
D P Q	27	28	D S P		D L P	27	28	D L P U
D E S P	29	30	D S P		D L P U	29	30	D L P
D E S P	31	32	ADC VDD REF OUT		D L	31	32	D L
A	33	34	ADC GND		D L Q	33	34	D E L
A	35	36	A		D L Q	35	36	D E L
A	37	38	A		D L U	37	38	D L U
A	39	40	A		D L P	39	40	D L P
D P	41	42	D Q S U P		D L P Q	41	42	D L P Q
GND	43	44	GND		D L P	43	44	D L P
GND	45	46	GND		D E L P	45	46	D E L P

This is an alternate starting point template that should be fully encompasing with indexes. It is a bit overwhelming, so I’m not making it visible.

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
USB D+	E1	E2	USB D-
5V OUT	E3	E4	GND
GND	1	2	GND		GND	1	2	GND
3V3 OUT	3	4	3V3 OUT		D M	3	4	D M
5V IN	5	6	5V IN		D M C4t	5	6	D M C4r
5V OUT	7	8	5V OUT		D C2r	7	8	D C2t
PWR BUT	9	10	RESET		D C3r	9	10	D C3t
D U4r	11	12	D		D P0o Q2b	11	12	D Q2a P0o
D U4t	13	14	D E1a		D E2b	13	14	D
D	15	16	D E1b		D P0i	15	16	D P0i
D I1c S00	17	18	D I1d S0o		D	17	18	D
C0r D I2c	19	20	C0t D I2d		D E2a	19	20	D M P1
D E0b S0i U2t	21	22	D E0a S0c U2r		D M P1	21	22	D M Q2b
D S01	23	24	C1r D I3c U1t		D M	23	24	D M
D P0	25	26	C1t D I3d U1r		D M	25	26	D
D P0 Q0b	27	28	D P0 S10		D L P1	27	28	D L P1 U6r
D E S1i P0	29	30	D P0 S1o		D L P1 U6t	29	30	D L P1
D E S1c P0	31	32	ADC VDD		D L	31	32	D L
A 4	33	34	ADC GND		D L Q1b	33	34	D E L
A 6	35	36	A 5		D L Q1a	35	36	D E L
A 2	37	38	A 3		D L U5t	37	38	D L U5r
A 0	39	40	A 1		D L P1	39	40	D L P1
D P0	41	42	D Q0a S11 U3t P0		D L P1 Q4a	41	42	D L P1 Q4b
GND	43	44	GND		D L P1	43	44	D L P1
GND	45	46	GND		D E L P1	45	46	D E L P1

Digital GPIO

The compatibility layer comes with simple reference nodes for attaching the Linux gpio-leds or gpio-keys to any cape header GPIO pin. This provides simple userspace general purpose input or output with various trigger modes.

The format followed for the gpio-leds nodes is bone_led_P8_## / bone_led_P9_##. The gpio-leds driver is used by these reference nodes internally and allows users to easily create compatible led nodes in overlays for Black, AI and AI-64.

Listing 15 Example device tree overlay to enable LED driver on header P8 pin 3

/dts-v1/;
/plugin/;

&bone_led_P8_03 {
    status = "okay";
}

In Example device tree overlay to enable LED driver on header P8 pin 3, it is possible to redefine the default label and other properties defined in the gpio-leds schema.

Table 102 GPIO pins

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
	3	4			P8_03	3	4	P8_04
	5	6			P8_05	5	6	P8_06
	7	8			P8_07	7	8	P8_08
	9	10			P8_09	9	10	P8_10
P9_11	11	12	P9_12		P8_11	11	12	P8_12
P9_13	13	14	P9_14		P8_13	13	14	P8_14
P9_15	15	16	P9_15		P8_15	15	16	P8_16
P9_17	17	18	P9_18		P8_17	17	18	P8_18
P9_19	19	20	P9_20		P8_19	19	20	P8_20
P9_21	21	22	P9_22		P8_21	21	22	P8_22
P9_23	23	24	P9_24		P8_23	23	24	P8_24
P9_25	25	26	P9_26		P8_25	25	26	P8_26
P9_27	27	28	P9_28		P8_27	27	28	P8_28
P9_29	29	30	P9_30		P8_29	29	30	P8_30
P9_31	31	32			P8_31	31	32	P8_32
	33	34			P8_33	33	34	P8_34
	35	36			P8_35	35	36	P8_36
	37	38			P8_37	37	38	P8_38
	39	40			P8_39	39	40	P8_40
P9_41	41	42	P9_42		P8_41	41	42	P8_42
	43	44			P8_43	43	44	P8_44
	45	46			P8_45	45	46	P8_46

Table 103 Bone GPIO LEDs interface

SYSFS link	Header pin	Black	AI	AI-64
/sys/class/leds/P8_03	P8_03	gpio1_6	gpio1_24	gpio0_20
/sys/class/leds/P8_04	P8_04	gpio1_7	gpio1_25	gpio0_48
/sys/class/leds/P8_05	P8_05	gpio1_2	gpio7_1	gpio0_33
/sys/class/leds/P8_06	P8_06	gpio1_3	gpio7_2	gpio0_34
/sys/class/leds/P8_07	P8_07	gpio2_2	gpio6_5	gpio0_15
/sys/class/leds/P8_08	P8_08	gpio2_3	gpio6_6	gpio0_14
/sys/class/leds/P8_09	P8_09	gpio2_5	gpio6_18	gpio0_17
/sys/class/leds/P8_10	P8_10	gpio2_4	gpio6_4	gpio0_16
/sys/class/leds/P8_11	P8_11	gpio1_13	gpio3_11	gpio0_60
/sys/class/leds/P8_12	P8_12	gpio1_12	gpio3_10	gpio0_59
/sys/class/leds/P8_13	P8_13	gpio0_23	gpio4_11	gpio0_89
/sys/class/leds/P8_14	P8_14	gpio0_26	gpio4_13	gpio0_75
/sys/class/leds/P8_15	P8_15	gpio1_15	gpio4_3	gpio0_61
/sys/class/leds/P8_16	P8_16	gpio1_14	gpio4_29	gpio0_62
/sys/class/leds/P8_17	P8_17	gpio0_27	gpio8_18	gpio0_3
/sys/class/leds/P8_18	P8_18	gpio2_1	gpio4_9	gpio0_4
/sys/class/leds/P8_19	P8_19	gpio0_22	gpio4_10	gpio0_88
/sys/class/leds/P8_20	P8_20	gpio1_31	gpio6_30	gpio0_76
/sys/class/leds/P8_21	P8_21	gpio1_30	gpio6_29	gpio0_30
/sys/class/leds/P8_22	P8_22	gpio1_5	gpio1_23	gpio0_5
/sys/class/leds/P8_23	P8_23	gpio1_4	gpio1_22	gpio0_31
/sys/class/leds/P8_24	P8_24	gpio1_1	gpio7_0	gpio0_6
/sys/class/leds/P8_25	P8_25	gpio1_0	gpio6_31	gpio0_35
/sys/class/leds/P8_26	P8_26	gpio1_29	gpio4_28	gpio0_51
/sys/class/leds/P8_27	P8_27	gpio2_22	gpio4_23	gpio0_71
/sys/class/leds/P8_28	P8_28	gpio2_24	gpio4_19	gpio0_72
/sys/class/leds/P8_29	P8_29	gpio2_23	gpio4_22	gpio0_73
/sys/class/leds/P8_30	P8_30	gpio2_25	gpio4_20	gpio0_74
/sys/class/leds/P8_31	P8_31	gpio0_10	gpio8_14	gpio0_32
/sys/class/leds/P8_32	P8_32	gpio0_11	gpio8_15	gpio0_26
/sys/class/leds/P8_33	P8_33	gpio0_9	gpio8_13	gpio0_25
/sys/class/leds/P8_34	P8_34	gpio2_17	gpio8_11	gpio0_7
/sys/class/leds/P8_35	P8_35	gpio0_8	gpio8_12	gpio0_24
/sys/class/leds/P8_36	P8_36	gpio2_16	gpio8_10	gpio0_8
/sys/class/leds/P8_37	P8_37	gpio2_14	gpio8_8	gpio0_106
/sys/class/leds/P8_38	P8_38	gpio2_15	gpio8_9	gpio0_105
/sys/class/leds/P8_39	P8_39	gpio2_12	gpio8_6	gpio0_69
/sys/class/leds/P8_40	P8_40	gpio2_13	gpio8_7	gpio0_70
/sys/class/leds/P8_41	P8_41	gpio2_10	gpio8_4	gpio0_67
/sys/class/leds/P8_42	P8_42	gpio2_11	gpio8_5	gpio0_68
/sys/class/leds/P8_43	P8_43	gpio2_8	gpio8_2	gpio0_65
/sys/class/leds/P8_44	P8_44	gpio2_9	gpio8_3	gpio0_66
/sys/class/leds/P8_45	P8_45	gpio2_6	gpio8_0	gpio0_79
/sys/class/leds/P8_46	P8_46	gpio2_7	gpio8_1	gpio0_80
/sys/class/leds/P9_11	P9_11	gpio0_30	gpio8_17	gpio0_1
/sys/class/leds/P9_12	P9_12	gpio1_28	gpio5_0	gpio0_45
/sys/class/leds/P9_13	P9_13	gpio0_31	gpio6_12	gpio0_2
/sys/class/leds/P9_14	P9_14	gpio1_18	gpio4_25	gpio0_93
/sys/class/leds/P9_15	P9_15	gpio1_16	gpio3_12	gpio0_47
/sys/class/leds/P9_16	P9_16	gpio1_19	gpio4_26	gpio0_94
/sys/class/leds/P9_17	P9_17	gpio0_5	gpio7_17	gpio0_28
/sys/class/leds/P9_18	P9_18	gpio0_4	gpio7_16	gpio0_40
/sys/class/leds/P9_19	P9_19	gpio0_13	gpio7_3	gpio0_78
/sys/class/leds/P9_20	P9_20	gpio0_12	gpio7_4	gpio0_77
/sys/class/leds/P9_21	P9_21	gpio0_3	gpio3_3	gpio0_39
/sys/class/leds/P9_22	P9_22	gpio0_2	gpio6_19	gpio0_38
/sys/class/leds/P9_23	P9_23	gpio1_17	gpio7_11	gpio0_10
/sys/class/leds/P9_24	P9_24	gpio0_15	gpio6_15	gpio0_13
/sys/class/leds/P9_25	P9_25	gpio3_21	gpio6_17	gpio0_127
/sys/class/leds/P9_26	P9_26	gpio0_14	gpio6_14	gpio0_12
/sys/class/leds/P9_27	P9_27	gpio3_19	gpio4_15	gpio0_46
/sys/class/leds/P9_28	P9_28	gpio3_17	gpio4_17	gpio1_11
/sys/class/leds/P9_29	P9_29	gpio3_15	gpio5_11	gpio0_53
/sys/class/leds/P9_30	P9_30	gpio3_16	gpio5_12	gpio0_44
/sys/class/leds/P9_31	P9_31	gpio3_14	gpio5_10	gpio0_52
/sys/class/leds/P9_33	P9_33	n/a	n/a	gpio0_50
/sys/class/leds/P9_35	P9_35	n/a	n/a	gpio0_55
/sys/class/leds/P9_36	P9_36	n/a	n/a	gpio0_56
/sys/class/leds/P9_37	P9_37	n/a	n/a	gpio0_57
/sys/class/leds/P9_38	P9_38	n/a	n/a	gpio0_58
/sys/class/leds/P9_39	P9_39	n/a	n/a	gpio0_54
/sys/class/leds/P9_40	P9_40	n/a	n/a	gpio0_81
/sys/class/leds/P9_41	P9_41	gpio0_20	gpio6_20	gpio1_0
/sys/class/leds/P9_42	P9_42	gpio0_7	gpio4_18	gpio0_123
/sys/class/leds/A15	A15 [7]	gpio0_19	NA	NA

[7]

On BeagleBone Black, A15 is used to enable or disable the external CEC clock generation for the HDMI framer.

I²C

Cape interface specification provides I²C controller device links for userspace interaction and defined device tree entries for creating compatible overlays for any compliant board and OS image. The device tree node are named as bone_i2c_#.

I²C pins

Table 104 I2C pins

P9
Functions	odd	even	Functions
1 SCL	17	18	1 SDA
2 SCL	19	20	2 SDA
4 SCL [4] [5]	21	22	4 SDA [4] [5]
	23	24	3 SCL [3]
	25	26	3 SDA [3]

[3] (1,2)

Port 3 is mutually exclusive with port 1 on Black

[4] (1,2)

Port 4 is mutually exclusive with port 2 on Black

[5] (1,2)

On Black and AI-64 only, not AI

I²C port mapping

Table 105 I2C port mapping

Links	DT symbol	Black	AI	AI-64	SCL	SDA	Overlay
/dev/bone/i2c/0	bone_i2c_0	I2C0	I2C1	WKUP_I2C0	On-board		BONE-I2C0
/dev/bone/i2c/1	bone_i2c_1	I2C1	I2C5	MAIN_I2C6	P9.17	P9.18	BONE-I2C1
/dev/bone/i2c/2	bone_i2c_2	I2C2	I2C4	MAIN_I2C3	P9.19	P9.20	BONE-I2C2
/dev/bone/i2c/3	bone_i2c_3	I2C1	I2C3	MAIN_I2C4	P9.24	P9.26	BONE-I2C3
/dev/bone/i2c/4	bone_i2c_4	I2C2	n/a	n/a	P9.21	P9.22	BONE-I2C4

Important

In the case the same controller is used for 2 different bone bus nodes, usage of those nodes is mutually-exclusive.

Note

The provided pre-compiled overlays enable the I²C bus driver only, not a specific device driver. Either a custom overlay is required to load the device driver or usermode device driver loading can be performed, depending on the driver. See Using I2C with Linux drivers for information on loading I²C drivers from userspace.

I²C overlay example

Listing 16 Example device tree overlay to enable I2C driver

/dts-v1/;
/plugin/;

&bone_i2c_1 {
    status = "okay";
    accel@1c {
        compatible = "fsl,mma8453";
        reg = <0x1c>;
    };
}

In Example device tree overlay to enable I2C driver, you can specify what driver you want to load and provide any properties it might need.

• https://www.kernel.org/doc/html/v5.10/i2c/summary.html

• https://www.kernel.org/doc/html/v5.10/i2c/instantiating-devices.html#method-1-declare-the-i2c-devices-statically

• https://www.kernel.org/doc/Documentation/devicetree/bindings/i2c/

I²C userspace example

See Using I2C with Linux drivers for examples on using the userspace links to load appropriate Linux kernel drivers.

SPI

SPI bone bus nodes allow creating compatible overlays for Black, AI and AI-64.

Table 106 SPI pins

P9
Functions	odd	even	Functions
0 CS0	17	18	0 SDO
	19	20
0 SDI	21	22	0 CLK
0 CS1	23	24
	25	26
	27	28	1 CS0
1 SDI	29	30	1 SDO
1 CLK	31	32
	33	34
	35	36
	37	38
	39	40
	41	42	1 CS1

Table 107 SPI port mapping

Bone bus	DT symbol	Black	AI	AI-64	SDO	SDI	CLK	CS	Overlay
/dev/bone/spi/0.0	bone_spi_0	SPI0	SPI2	MAIN_SPI6	P9.18	P9.21	P9.22	P9.17 (CS0)	BONE-SPI0_0
/dev/bone/spi/0.1								P9.23 (CS1)	BONE-SPI0_1
/dev/bone/spi/1.0	bone_spi_1	SPI1	SPI3	MAIN_SPI7	P9.30	P9.29	P9.31	P9.28 (CS0)	BONE-SPI1_0
/dev/bone/spi/1.1								P9.42 (CS1)	BONE-SPI1_1

Note

The provided pre-compiled overlays enable the “spidev” driver using the “rohm,dh2228fv” compatible string. See https://stackoverflow.com/questions/53634892/linux-spidev-why-it-shouldnt-be-directly-in-devicetree for more background. A custom overlay is required to overload the compatible string to load a non-spidev driver.

Todo

figure out if BONE-SPI0_0 and BONE-SPI0_1 can be loaded at the same time

Note

Some boards may implement CS using a GPIO.

Listing 17 Example device tree overlay to enable SPI driver

/dts-v1/;
/plugin/;

&bone_spi_0 {
    status = "okay";
     pressure@0 {
         compatible = "bosch,bmp280";
         reg = <0>;      /* CS0 */
         spi-max-frequency = <5000000>;
     };
}

In Example device tree overlay to enable SPI driver, you can specify what driver you want to load and provide any properties it might need.

• https://www.kernel.org/doc/html/v5.10/spi/spi-summary.html

• https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/

UART

UART bone bus nodes allow creating compatible overlays for Black, AI and AI-64.

Table 108 UART pins

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
4 RX [6]	11	12				11	12
4 TX [6]	13	14				13	14
	15	16				15	16
	17	18				17	18
	19	20				19	20
2 TX	21	22	2 RX			21	22	7 RX
	23	24	1 TX			23	24
	25	26	1 RX			25	26
	27	28				27	28	6 RX
	29	30			6 TX	29	30
	31	32				31	32
	33	34				33	34	7 TX
	35	36				35	36
	37	38			5 TX	37	38	5 RX
	39	40				39	40
	41	42	3 TX			41	42

Important

RTSn and CTSn mappings are not compatible across boards in the family and are therefore not part of the cape specification.

Table 109 UART port mapping

Bone bus	DT symbol	Black	AI	AI-64	TX	RX	Overlay
/dev/bone/uart/0	bone_uart_0	UART0	UART1	MAIN_UART0	Console debug header pins
/dev/bone/uart/1	bone_uart_1	UART1	UART10	MAIN_UART2	P9.24	P9.26	BONE-UART1
/dev/bone/uart/2	bone_uart_2	UART2	UART3	n/a	P9.21	P9.22	BONE-UART2
/dev/bone/uart/3	bone_uart_3	UART3	n/a	n/a	P9.42	n/a	BONE-UART3
/dev/bone/uart/4	bone_uart_4	UART4	UART5	MAIN_UART0 [6]	P9.13	P9.11	BONE-UART4
/dev/bone/uart/5	bone_uart_5	UART5	UART8	MAIN_UART5	P8.37	P8.38	BONE-UART5
/dev/bone/uart/6	bone_uart_6	n/a	n/a	MAIN_UART8	P8.29	P8.28	BONE-UART6
/dev/bone/uart/7	bone_uart_7	n/a	n/a	MAIN_UART2	P8.34	P8.22	BONE-UART7

[6] (1,2,3)

This port is shared with the console UART on AI-64

Important

In the case the same controller is used for 2 different bone bus nodes, usage of those nodes is mutually-exclusive.

CAN

CAN bone bus nodes allow creating compatible overlays for Black, AI and AI-64.

Table 110 CAN pins

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
	5	6			4 TX	5	6	4 RX
	7	8			2 RX	7	8	2 TX
	9	10			3 RX	9	10	3 TX
	11	12				11	12
	13	14				13	14
	15	16				15	16
	17	18				17	18
0 RX	19	20	0 TX			19	20
	21	22				21	22
	23	24	1 RX			23	24
	25	26	1 TX			25	26

Table 111 CAN port mapping

Bone bus	Black	AI	AI-64	TX	RX	Overlays
/dev/bone/can/0	CAN0	n/a	MAIN_MCAN0	P9.20	P9.19	BONE-CAN0
/dev/bone/can/1	CAN1	CAN2	MAIN_MCAN4	P9.26	P9.24	BONE-CAN1
/dev/bone/can/2	n/a	CAN1 [1]	MAIN_MCAN5	P8.08	P8.07	BONE-CAN2
/dev/bone/can/3	n/a	n/a	MAIN_MCAN6	P8.10	P8.09	BONE-CAN3
/dev/bone/can/4	n/a	n/a	MAIN_MCAN7	P8.05	P8.06	BONE-CAN4

[1]

BeagleBone AI rev A2 and later only

ADC

Todo

We need a udev rule to make sure the ADC shows up at /dev/bone/adc! There’s nothing for sure that IIO devices will show up in the same place.

Todo

I think we can also create symlinks for each channel based on which device is there, such that we can do /dev/bone/adc/Px_y

Todo

I believe a multiplexing IIO driver is the future solution

Table 112 ADC pins

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
USB D+	E1	E2	USB D-
5V OUT	E3	E4	GND
GND	1	2	GND		GND	1	2	GND
3V3 OUT	3	4	3V3 OUT		D M	3	4	D M
5V IN	5	6	5V IN		D M C4t	5	6	D M C4r
5V OUT	7	8	5V OUT		D C2r	7	8	D C2t
PWR BUT	9	10	RESET		D C3r	9	10	D C3t
D U4r	11	12	D		D P0o	11	12	D Q2a P0o
D U4t	13	14	D E1a		D E2b	13	14	D
D	15	16	D E1b		D P0i	15	16	D P0i
D I1c S00	17	18	D I1d S0o		D	17	18	D
C0r D I2c	19	20	C0t D I2d		D E2a	19	20	D M P1
D E0b S0i U2t	21	22	D E0a S0c U2r		D M P1	21	22	D M Q2b
D S01	23	24	C1r D I3c U1t		D M	23	24	D M
D P0	25	26	C1t D I3d U1r		D M	25	26	D
D P0 Q0b	27	28	D P0 S10		D L P1	27	28	D L P1 U6r
D E S1i P0	29	30	D P0 S1o		D L P1 U6t	29	30	D L P1
D E S1c P0	31	32	ADC VDD		D L	31	32	D L
A 4	33	34	ADC GND		D L Q1b	33	34	D E L
A 6	35	36	A 5		D L Q1a	35	36	D E L
A 2	37	38	A 3		D L U5t	37	38	D L U5r
A 0	39	40	A 1		D L P1	39	40	D L P1
D P0	41	42	D Q0a S11 U3t P0		D L P1	41	42	D L P1
GND	43	44	GND		D L P1	43	44	D L P1
GND	45	46	GND		D E L P1	45	46	D E L P1

Table 113 Bone ADC

Index	Header pin	Black/AI-64	AI
0	P9_39	in_voltage0_raw	in_voltage0_raw
1	P9_40	in_voltage1_raw	in_voltage1_raw
2	P9_37	in_voltage2_raw	in_voltage3_raw
3	P9_38	in_voltage3_raw	in_voltage2_raw
4	P9_33	in_voltage4_raw	in_voltage7_raw
5	P9_36	in_voltage5_raw	in_voltage6_raw
6	P9_35	in_voltage6_raw	in_voltage4_raw

Table 114 Bone ADC Overlay

Black	AI	AI-64	overlay
Internal	External (STMPE811)	TBD	BONE-ADC.dts

PWM

Todo

remove deep references to git trees

PWM bone bus nodes allow creating compatible overlays for Black, AI and AI-64. For the definitions, you can see bbai-bone-buses.dtsi#L415 & bbb-bone-buses.dtsi#L432

PWM pins

Table 115 PWM pins

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
	13	14	1 A		2 B	13	14
	15	16	1 B			15	16
	17	18				17	18
	19	20			2 A	19	20
0 B	21	22	0 A			21	22

PWM port mapping

Table 116 Bone bus PWM

SYSFS link	DT symbol	Black	AI	AI-64	A	B	Overlay
/dev/bone/pwm/0	bone_pwm_0	PWM0		PWM1	P9.22	P9.21	BONE-PWM0
/dev/bone/pwm/1	bone_pwm_0	PWM1	PWM3	PWM2	P9.14	P9.16	BONE-PWM1
/dev/bone/pwm/2	bone_pwm_0	PWM2	PWM2	PWM0	P8.19	P8.13	BONE-PWM2

PWM overlay example

Listing 18 Example device tree overlay to enable PWM driver

/dts-v1/;
/plugin/;

&bone_pwm_0 {
    status = "okay";
}

In Example device tree overlay to enable PWM driver, you can specify what driver you want to load and provide any properties it might need.

• https://www.kernel.org/doc/html/v5.10/driver-api/pwm.html

• https://www.kernel.org/doc/Documentation/devicetree/bindings/pwm/

PWM userspace example

See Fading an External LED and Motors for examples on using the userspace links to use the PWMs.

TIMER PWM

TIMER PWM bone bus uses ti,omap-dmtimer-pwm driver, and timer nodes that allow creating compatible overlays for Black, AI and AI-64. For the timer node definitions, you can see bbai-bone-buses.dtsi#L449 & bbb-bone-buses.dtsi#L466.

Table 117 Bone TIMER PWMs

Bone bus	Header pin	Black	AI	overlay
/sys/bus/platform/devices/bone_timer_pwm_0/	P8.10	timer6	timer10	BONE-TIMER_PWM_0.dts
/sys/bus/platform/devices/bone_timer_pwm_1/	P8.07	timer4	timer11	BONE-TIMER_PWM_1.dts
/sys/bus/platform/devices/bone_timer_pwm_2/	P8.08	timer7	timer12	BONE-TIMER_PWM_2.dts
/sys/bus/platform/devices/bone_timer_pwm_3/	P9.21		timer13	BONE-TIMER_PWM_3.dts
/sys/bus/platform/devices/bone_timer_pwm_4/	P8.09	timer5	timer14	BONE-TIMER_PWM_4.dts
/sys/bus/platform/devices/bone_timer_pwm_5/	P9.22		timer15	BONE-TIMER_PWM_5.dts

Counter

A counter function for quadrature encoders is implemented with the EQEP peripheral.

Todo

Additional quadrature encoders can be implemented in PRU firmware.

Table 118 Counter pins

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
	11	12			2 B	11	12	2 A
	13	14				13	14
	15	16			3 B	15	16	3 A
	17	18				17	18
	19	20				19	20
	21	22				21	22
	23	24				23	24
	25	26				25	26
0 B	27	28				27	28
	29	30				29	30
	31	32				31	32
	33	34			1 B	33	34
	35	36			1 A	35	36
	37	38				37	38
	39	40				39	40
	41	42	0 A			41	42

On BeagleBone’s without an eQEP on specific pins, consider using the PRU to perform a software counter function.

Table 119 Counter port mapping

SYSFS link	DT symbol	Black	AI	AI-64	A	B	STRB	INDX	Overlay
/dev/bone/counter/0	bone_counter_0	eQEP0	eQEP2	eQEP0	P9.42	P9.27	Black/AI-64: P9.25 AI: P8.06	Black/AI-64: P9.41 AI: P8.05	BONE-COUNTER0
/dev/bone/counter/1	bone_counter_1	eQEP1	eQEP0	eQEP1	P8.35	P8.33	Black/AI-64: P8.32 AI: P9.21	Black/AI-64: P8.31 AI: ‒	BONE-COUNTER1
/dev/bone/counter/2	bone_counter_2	eQEP2	eQEP1	‒	P8.12	P8.11	Black: P8.15 AI: P8.18	Black: P8.16 AI: P9.15	BONE-COUNTER2
/dev/bone/counter/3	bone_counter_3	eQEP2	‒	‒	P8.41	P8.42	Black: P8.40	Black: P8.39	BONE-COUNTER3
/dev/bone/counter/4	bone_counter_4	‒	‒	‒	P8.16	P8.15			BONE-COUNTER4

eCAP

Todo

This doesn’t include any abstraction yet.

Table 120 ECAP pins

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
USB D+	E1	E2	USB D-
5V OUT	E3	E4	GND
GND	1	2	GND		GND	1	2	GND
3V3 OUT	3	4	3V3 OUT		D M	3	4	D M
5V IN	5	6	5V IN		D M C4t	5	6	D M C4r
5V OUT	7	8	5V OUT		D C2r	7	8	D C2t
PWR BUT	9	10	RESET		D C3r	9	10	D C3t
D U4r	11	12	D		D P0o	11	12	D Q2a P0o
D U4t	13	14	D E1a		D E2b	13	14	D
D	15	16	D E1b		D P0i	15	16	D P0i
D I1c S00	17	18	D I1d S0o		D	17	18	D
C0r D I2c	19	20	C0t D I2d		D E2a	19	20	D M P1
D E0b S0i U2t	21	22	D E0a S0c U2r		D M P1	21	22	D M Q2b
D S01	23	24	C1r D I3c U1t		D M	23	24	D M
D P0	25	26	C1t D I3d U1r		D M	25	26	D
D P0 Q0b	27	28	D P0 S10		D L P1	27	28	D L P1 U6r
D E S1i P0	29	30	D P0 S1o		D L P1 U6t	29	30	D L P1
D E S1c P0	31	32	ADC VDD		D L	31	32	D L
A 4	33	34	ADC GND		D L Q1b	33	34	D E L
A 6	35	36	A 5		D L Q1a	35	36	D E L
A 2	37	38	A 3		D L U5t	37	38	D L U5r
A 0	39	40	A 1		D L P1	39	40	D L P1
D P0	41	42	D Q0a S11 U3t P0		D L P1	41	42	D L P1
GND	43	44	GND		D L P1	43	44	D L P1
GND	45	46	GND		D E L P1	45	46	D E L P1

Table 121 Black eCAP PWMs

Bone bus	Header pin	peripheral	overlay
/sys/bus/platform/drivers/ecap/48302100.ecap	P9.42	eCAP0_in_PWM0_out	BBB-ECAP0.dts
/sys/bus/platform/drivers/ecap/48304100.ecap	P9.28	eCAP2_in_PWM2_out	BBB-ECAP2.dts

Table 122 AI eCAP PWMs

Bone bus	Header pin	peripheral	overlay
/sys/bus/platform/drivers/ecap/4843e100.ecap	P8.15	eCAP1_in_PWM1_out	BBAI-ECAP1.dts
/sys/bus/platform/drivers/ecap/48440100.ecap	P8.14	eCAP2_in_PWM2_out	BBAI-ECAP2.dts
/sys/bus/platform/drivers/ecap/48440100.ecap	P8.20	eCAP2_in_PWM2_out	BBAI-ECAP2A.dts
/sys/bus/platform/drivers/ecap/48442100.ecap	P8.04	eCAP3_in_PWM3_out	BBAI-ECAP3.dts
/sys/bus/platform/drivers/ecap/48442100.ecap	P8.26	eCAP3_in_PWM3_out	BBAI-ECAP3A.dts

MMC/SDIO

SDIO is popular to connect various WiFi modules. The interface can also be used to connect MMC cards.

Important

On Black, the SDIO pins are consumed by default by the on-board eMMC which must be disabled to utilize the SDIO capability. On AI and AI-64, the on-board eMMC does not consume these pins.

Table 123 Bone MMC/SD/SDIO/eMMC

Header pin	Description
P8.3	DAT6 [9]
P8.4	DAT7 [9]
P8.5	DAT2
P8.6	DAT3
P8.20	CMD
P8.21	CLK
P8.22	DAT5 [9]
P8.23	DAT4 [9]
P8.24	DAT1
P8.25	DAT0

[9] (1,2,3,4)

8-bit eMMC support only on Black. AI and AI-64 provide 4-bit support only.

Table 124 Bone SDIO Overlay

Black	AI	overlay
MMC2	MMC3	BONE-SDIO

LCD

Table 125 16bit LCD interface

Header pin	Black	AI	RGB565
P8_27	lcd_vsync	vout1__vsync	VSYNC
P8_28	lcd_pclk	vout1_pclk	PCLK
P8_29	lcd_hsync	vout1_hsync	HSYNC
P8_30	lcd_ac_bias_en	vout1_de	DE
P8_32	lcd_data15	vout1_d15	R4
P8_31	lcd_data14	vout1_d14	R3
P8_33	lcd_data13	vout1_d13	R2
P8_35	lcd_data12	vout1_d12	R1
P8_34	lcd_data11	vout1_d11	R0
P8_36	lcd_data10	vout1_d10	G5
P8_38	lcd_data9	vout1_d9	G4
P8_37	lcd_data8	vout1_d8	G3
P8_40	lcd_data7	vout1_d7	G2
P8_39	lcd_data6	vout1_d6	G1
P8_42	lcd_data5	vout1_d5	G0
P8_41	lcd_data4	vout1_d4	B4
P8_44	lcd_data3	vout1_d3	B3
P8_43	lcd_data2	vout1_d2	B2
P8_46	lcd_data1	vout1_d1	B1
P8_45	lcd_data0	vout1_d0	B0

Table 126 16bit LCD interface Overlay

Black	AI	overlay
lcdc	dss

I²S

Todo

Describe I²S and ALSA

I²S pins

Table 127 I²S pins

P9					P8
Functions	odd	even	Functions		Functions	odd	even	Functions
	11	12	0 SCK_IN			11	12
	13	14				13	14
	15	16				15	16
	17	18				17	18
	19	20				19	20
	21	22				21	22
	23	24				23	24
0 HCLK	25	26				25	26
0 WS_IN	27	28	0 SDO0			27	28
0 WS	29	30	0 SDI0			29	30
0 SCK	31	32			0 SDO1 [8]	31	32
	33	34			0 SDI1 [8]	33	34

[8] (1,2)

Only available on Black.

Important

I²S 0 is used by HDMI audio on Black.

I²S port mapping

Table 128 I²S port mapping

I2S	Header pin	Black	AI	AI-64
HCLK	P9.25	mcasp0_ahclkx	mcasp1_ahclkx	AUDIO_EXT_REFCLK2
SCLK	P9.31	mcasp0_aclkx	mcasp1_aclkx	MCASP0_ACLKX
SCLK_IN	P9.12	mcasp0_aclkr_mux3	mcasp1_aclkr	MCASP0_ACLKR
WS	P9.29	mcasp0_fsx	mcasp1_fsx	MCASP0_AFSX
WS_IN	P9.27	mcasp0_fsr	mcasp1_fsr	MCASP0_AFSR
SDO0	P9.28	mcasp0_axr2	mcasp1_axr11	MCASP0_AXR0
SDI0	P9.30	mcasp0_axr0	mcasp1_axr10	MCASP0_AXR1
SDO1	P8.31	mcasp0_axr1
SDI1	P8.33	mcasp0_axr3

Table 129 I²S port mapping link and overlay

Link	Overlays
/dev/bone/i2s/0	BONE-I2S0

I²S overlay example

PRU

The overlay situation for PRUs is a bit more complex than with other peripherals. The mechanism for loading, starting and stopping the PRUs can go through either UIO or RemoteProc.

• /dev/remoteproc/prussX-coreY (AM3358 X = “”, other x = “1|2”)

Table 130 Bone PRU eCAP

Header Pin	Black	AI
P8.15	pr1_ecap0	pr1_ecap0
P8.32		pr2_ecap0
P9.42	pr1_ecap0

Table 131 AI PRU UART

UART	TX	RX	RTSn	CTSn	Overlays
PRU1 UART0	P8_31	P8_33	P8_34	P8_35
PRU2 UART0	P8_43	P8_44	P8_45	P8_46

Table 132 Bone PRU

Header Pin	Black	AI
P8.03		pr2_pru0 10
P8.04		pr2_pru0 11
P8.05		pr2_pru0 06
P8.06		pr2_pru0 07
P8.07		pr2_pru1 16
P8.08		pr2_pru0 20
P8.09		pr2_pru1 06
P8.10		pr2_pru1 15
P8.11	pr1_pru0 15 (Out)	pr1_pru0 04
P8.12	pr1_pru0 14 (Out)	pr1_pru0 03
P8.13		pr1_pru1 07
P8.14		pr1_pru1 09
P8.15	pr1_pru0 15 (In)	pr1_pru1 16
P8.16	pr1_pru0 14 (In)	pr1_pru1 18
P8.17		pr2_pru0 15
P8.18		pr1_pru1 05
P8.19		pr1_pru1 06
P8.20		pr2_pru0 03
P8.21		pr2_pru0 02
P8.22		pr2_pru0 09
P8.23		pr2_pru0 08
P8.24		pr2_pru0 05
P8.25		pr2_pru0 04
P8.26		pr1_pru1 17
P8.27		pr2_pru1 17
P8.28		pr2_pru0 17
P8.29		pr2_pru0 18
P8.30		pr2_pru0 19
P8.31		pr2_pru0 11
P8.32		pr2_pru1 00
P8.33		pr2_pru0 10
P8.34		pr2_pru0 08
P8.35		pr2_pru0 09
P8.36		pr2_pru0 07
P8.37		pr2_pru0 05
P8.38		pr2_pru0 06
P8.39		pr2_pru0 03
P8.40		pr2_pru0 04
P8.41		pr2_pru0 01
P8.42		pr2_pru0 02
P8.43		pr2_pru1 20
P8.44		pr2_pru0 00
P8.45		pr2_pru1 18
P8.46		pr2_pru1 19
P9.11		pr2_pru0 14
P9.13		pr2_pru0 15
P9.14		pr1_pru1 14
P9.15		pr1_pru0 5
P9.16		pr1_pru1 15
P9.17		pr2_pru1 09
P9.18		pr2_pru1 08
P9.19		pr1_pru1 02
P9.20		pr1_pru1 01
P9.24	pr1_pru0 16 (In)
P9.25	pr1_pru0 07	pr2_pru1 05
P9.26	pr1_pru1 16 (In)	pr1_pru0 17
P9.27	pr1_pru0 05	pr1_pru1 11
P9.28	pr1_pru0 03	pr2_pru1 13
P9.29	pr1_pru0 01	pr2_pru1 11
P9.30	pr1_pru0 02	pr2_pru1 12
P9.31	pr1_pru0 00	pr2_pru1 10
P9.41	pr1_pru0 06	pr1_pru1 03
P9.42	pr1_pru0 04	pr1_pru1 10

Dynamic overlays

Todo

Document dynamic DT overlays

Dynamic pinmux control

Todo

Document dynamic pinmux control

Methodology

The methodology for applied in the kernel and software images to expose the software interfaces is to be documented here. The most fundamental elements are the device tree entries, including overlays, and udev rules.

Device Trees

Todo

Describe how the Device Trees expose symbols for reuse across boards

For every resource exposed on the cape headers, an indexed symbol should be provided in the base device tree.

udev rules

10-of-symlink.rules

#From: https://github.com/mvduin/py-uio/blob/master/etc/udev/rules.d/10-of-symlink.rules
# allow declaring a symlink for a device in DT
ATTR{device/of_node/symlink}!="", \
        ENV{OF_SYMLINK}="%s{device/of_node/symlink}"

ENV{OF_SYMLINK}!="", ENV{DEVNAME}!="", \
        SYMLINK+="%E{OF_SYMLINK}", \
        TAG+="systemd", ENV{SYSTEMD_ALIAS}+="/dev/%E{OF_SYMLINK}"

TBD

# Also courtesy of mvduin
# create symlinks for gpios exported to sysfs by DT
SUBSYSTEM=="gpio", ACTION=="add", TEST=="value", ATTR{label}!="sysfs", \
                RUN+="/bin/mkdir -p /dev/bone/gpio", \
                RUN+="/bin/ln -sT '/sys/class/gpio/%k' /dev/bone/gpio/%s{label}"

Verification

Todo

The steps used to verify all of these configurations is to be documented here. It will serve to document what has been tested, how to reproduce the configurations, and how to verify each major triannual release. All faults will be documented in the issue tracker.

References

• Device Tree: Supporting Similar Boards - The BeagleBone Example

• Google drive with summary of expansion signals on various BeagleBoard.org designs

• Beagleboard:Cape Expansion Headers